Custom Cleaning Brush
Paper Making Brush
Paper Making Brush provides controlled brush contact for panel, film, and paper across flat panels, films, and sheets. Working width, brush geometry, mounting, and fill are set around the machine path and the way dust, fibers, and fines must be released or carried away.
Product Features
Roller or strip contact removes fibers, dust, and coating particles — The brush supports cleaner paper webs and machine surfaces.
Horsehair provides soft cleaning on delicate paper and polished rolls — Fine natural bristles lift loose particles with low pressure.
Nylon or PBT supplies resilient synthetic contact — Filament selection can address wet use, recovery, and firmer cleaning requirements.
Roller format spans a moving web or machine surface — Straight or spiral tufting can clean uniformly or direct residue.
Strip format reaches guides, edges, and confined machine zones — The linear brush installs where a full-width roller is unnecessary.
Configured to the paper machine — Width, roller diameter or strip profile, fill, trim, pattern, core or channel, shaft ends, and mounting can be customized.
Product Overview
Paper Making Brush is used where repeatable contact is needed across flat panels, films, and sheets rather than isolated hand cleaning. The active brush face clears dust, fibers, and fines while the holder, shaft, plate, or hub stays outside the interference path and supports the required working width. The brush must maintain uniform low-load contact across the active width without wrinkling or marking the surface.
Key dimensions start with Brush head diameter 50–300 mm and Brush head length 100–4500 mm. This product uses a roller or conveyor-brush structure for continuous contact across a moving or wide surface. The specified interface is shaft-mounted / fixed. Nylon PA, PBT, and Horsehair are the principal material directions in the current specification. Please send the equipment interface and operating conditions, including speed, so the brush can be matched to the machine.
Technical Specifications
| Working width | 100–4500 mm |
|---|---|
| Roller diameter | 50–300 mm |
| Trim length | 10–60 mm |
| Filament diameter | 0.05–0.40 mm |
| Mounting | Bearing shaft, holder, or machine bar |
| Contact setting | Use 1–5 mm engagement and keep brush runout below the allowable web-thickness variation. |
| Fill materials | Nylon PA, PBT, and Horsehair |
| Cleaning zone | panel, film, paper, and continuous-surface cleaning |
| Contact surface | flat panels, films, sheets, rolls, coated webs, glass, and production surfaces |
| Residue class | dust, fibers, fines, oil film |
| Access and motion | the brush must maintain uniform low-load contact across the active width without wrinkling or marking the surface |
| Configuration focus | Web guiding, sheet support, spreading, or process-line brushing duty |
| Cleaning duty | panel, film, paper on flat panels, films, sheets, rolls |
| Variant configuration | Paper Making Brush: roller, strip construction with Nylon PA, PBT, Horsehair fill for panel, film, paper, and continuous-surface cleaning on flat panels, films, sheets, rolls. |
Application Areas
Paper Making Brush is primarily mapped to Textile Dyeing, Printing & Finishing Brush Use. If the brush will be used on a different job, confirm the surface, debris discharge path, and acceptable finish first.
- Paper Making Brush is best suited to paper, film, foil, textile, and web cleaning, spreading, guiding, or static control.
- The web-spreader, cleaning roller, horsehair wheel, or process cylinder brush follows moving paper, film, foil, nonwoven, textile, and coated web surfaces while the fill displaces dust, fibres, loose particles, trim residue, and static-held contamination.
- Use this configuration when the available access supports controlled low-load contact on moving paper, textile, film, fiberglass, or nonwoven webs.
Selection Guidance
Structure fit
Match the roller and conveyor brush geometry to flat panels, films, and sheets, the available access, and powered operation. Confirm Brush head diameter 50–300 mm and Brush head length 100–4500 mm against the complete working envelope before finalizing the brush.
Contact material
Choose from Nylon PA, PBT, and Horsehair according to the behavior of dust, fibers, and fines, the surface sensitivity, and any wet, chemical, temperature, or hygiene requirements. Material is only one part of stiffness; filament diameter, exposed length, and density must also be confirmed.
When to use another solution
For Paper Making Brush, use another cleaning method when dust, fibers, and fines cannot be released by controlled filament contact, when flat panels, films, and sheets cannot tolerate the selected contact material, or when the access path prevents safe engagement and residue removal.
Customization Options
| Brush Head Diameter (mm) | 50–300 |
|---|---|
| Brush Head Length (mm) | 100–4500 |
| Handle Length (mm) | Not Applicable (No separate handle in this product configuration) |
| Handle Grip Diameter (mm) | Not Applicable (No explicit grip or handle-diameter dimension in the product specification) |
| Bristle Material | Nylon PA, PBT, Horsehair |
| Handle Material | 6061 Aluminum Alloy |
| Mounting / Interface | Shaft-Mounted / Fixed |
| Grip Style | Not Applicable (Machine-Mounted Brush) |
| Color | Custom PANTONE Color ([Industry Reference Range]) |
| Logo Process | Laser Engraving / Screen Printing / Pad Printing ([Industry Reference Range]) |
| Surface Treatment | Smooth / Textured / Overmolded / Coated (Depending on Substrate; [Industry Reference Range]) |
Frequently Asked Questions
How should Paper Making Brush be selected?
Start with paper, film, foil, textile, and web cleaning, spreading, guiding, or static control, moving paper, film, foil, nonwoven, textile, and coated web surfaces, and dust, fibres, loose particles, trim residue, and static-held contamination. Then set Working width, Roller diameter, and Trim length, choose the fill from the material and residue table, and match the mounting interface and operating condition.
Which dimensions define Paper Making Brush?
The primary dimensions are Working width (100–4500 mm), Roller diameter (50–300 mm), and Trim length (10–60 mm). Also provide the minimum clearance, working envelope, trim or engagement, and the existing holder, shaft, stem, thread, or handle.
Which filament or contact material is used for Paper Making Brush?
The primary options are Nylon PA, PBT, and Horsehair. The final choice follows surface sensitivity, residue adhesion, wet or dry use, temperature, chemicals, conductivity, and required cutting action.
When is Paper Making Brush not the best cleaning method?
Paper Making Brush is not the first choice for bowed rollers, air bars, vacuum, ionizers, tack rollers, or non-contact spreaders for highly tension-sensitive webs.
What information is required to quote Paper Making Brush?
Send the part or machine drawing, photos of moving paper, film, foil, nonwoven, textile, and coated web surfaces, Working width, Roller diameter, Trim length, and Filament diameter, the residue description, wet or dry conditions, motion or use method, temperature, preferred Nylon PA, PBT, and Horsehair, quantity, and the existing interface or sample.
RELATED BRUSH RESOURCES
Recommended Reading & Related Brush Resources
Custom Roller and Conveyor Brushes
Choose a roller or conveyor brush when a cylindrical brush must clean, wipe, guide,…
Explore this brush type
Textile Dyeing, Printing & Finishing Brush Use
Textile Dyeing, Printing & Finishing Brush Use is a process-use page rather than a…
Review application guidance
Automatic Shoe Polishing & Footwear Surface Brushing
Automatic Shoe Polishing & Footwear Surface Brushing is treated as a configurable manufacturing capability.
Review application guidance
Nylon PA
Nylon PA is selected from its stiffness, recovery, wear, wet-service, chemical, and temperature behavior.
Compare material considerations
PBT
PBT is selected from its stiffness, recovery, wear, wet-service, chemical, and temperature behavior. Do…
Compare material considerationsCustom Manufacturing RFQ
Upload the Brush Drawing, Product Photo or Sample Details
For an accurate quotation, please provide the main dimensions, material preference, working surface, residue, quantity, and a drawing or photo.
Custom Brush RFQ
Send Your Brush Project
Upload a drawing, product photo, or sample photo and provide the core dimensions and cleaning conditions.