120mm PA66 Duct Cleaning Brush
Round 120mm PA66 duct cleaning brush on a stainless twisted core for HVAC duct, vent and fin cleaning.
- Head Ø
- 120 mm
- Head length
- 300 mm
- Handle
- 600 mm
PRODUCT CATEGORY
HVAC, Vent & Coil Cleaning Brushes
Airflow equipment collects dust where access is long and surfaces are often easy to deform. Duct interiors, dryer vents and ventilation runs need reach; evaporator and condenser fins need much lighter contact. This category separates those jobs so cleaning force is not applied where it can damage airflow components.
Browse Duct, Vent, Coil and Fin Brushes
Choose flexible duct and dryer-vent brushes for internal runs, coil and fin brushes for heat exchangers, or compact vent brushes for accessible grilles and equipment openings.
150mm PP Ventilation Brush
Order the 150mm PP ventilation brush with twisted stainless steel core and quick-change coupling.
- Head Ø
- 150 mm
- Head length
- 350 mm
- Handle
- 650 mm
200mm PA66 Large Duct Brush
200mm PA66 large duct brush with a 400 mm head, 800 mm twist-core handle and quick-change coupling.
- Head Ø
- 200 mm
- Head length
- 400 mm
- Handle
- 800 mm
AC Cleaning Brush
Long-reach AC cleaning brush for filters, vents, coil fins, and fan housings.
- Head Ø
- 10–60 mm
- Head length
- 50–250 mm
- Handle
- 300–700 mm
AC Fin Cleaning Brush
Custom AC fin cleaning brush with PBT, PP, or nylon filaments to clean condenser and evaporator coils.
- Head Ø
- 10–60 mm
- Head length
- 50–250 mm
- Handle
- 300–700 mm
Air Conditioner Cleaning Brush
Custom air conditioner cleaning brush for HVAC maintenance.
- Head Ø
- 3–100 mm
- Head length
- 10–120 mm
- Handle
- 120–450 mm
Air Duct Cleaning Brush
Rotary air duct cleaning brush with flexible shaft reach of 5–30 m, Nylon PA or PP filaments.
- Head Ø
- 200–600 mm
Dryer Vent Cleaning Brush
Flexible dryer vent cleaning brush clears lint, dust, and pet hair from 3–6 inch ducts. Modular rods reach 1–10 m.
- Head Ø
- 102–140 mm
Evaporator Coil Cleaning Brush
Clean evaporator and condenser coils without bending fins.
- Head Ø
- 10–60 mm
- Head length
- 50–250 mm
- Handle
- 300–700 mm
Flexible Rod Brush
Twisted-wire flexible rod brush with nylon or polyester fill for curved pipes, flues, chimneys and bores.
- Head Ø
- 3.2–50.8 mm
- Handle
- 152–406 mm
Heat Sink Fin Brush
Fine nylon or PBT filaments slip between fins spaced 1 to 6 mm and lift oily particulate.
- Head Ø
- 10–60 mm
- Head length
- 50–250 mm
- Handle
- 300–700 mm
Radiator Fin Brush
Custom radiator fin brush with brass wire or Nylon PA fill for HVAC coil and heat-exchanger cleaning.
- Head Ø
- 10–60 mm
- Head length
- 50–250 mm
- Handle
- 300–700 mm
Refrigerator Condenser Cleaning Brush
Custom refrigerator condenser cleaning brush with soft anti-static nylon/PBT filaments.
- Head Ø
- 10–60 mm
- Head length
- 50–250 mm
- Handle
- 300–700 mm
Long Stainless Flexible Brush
Long stainless flexible brush for duct, vent, chimney and pipe cleaning.
Is the Problem Reach or Surface Fragility?
Long ducts and delicate fins can both look like “HVAC cleaning,” but they require opposite brush behavior. Identify the limiting condition first.
Duct or vent diameter
Internal duct brushes need a working diameter that reaches the wall without becoming impossible to push, pull or rotate through the passage.
Fin spacing and fragility
Evaporator, condenser and radiator fins can bend under excessive force, so trim stiffness and contact pressure must be controlled.
Straight run or bends
Flexible rods and shafts are useful for dryer vents and ductwork with depth or bends; rigid hand tools suit accessible grilles and coils.
Dust, lint or bonded contamination
Loose lint and dust need pickup and transport; greasy or adhered deposits may require chemistry and a different cleaning process rather than simply a stiffer brush.
Duct Brushes and Fin Brushes Should Not Be Selected Together
A duct brush needs enough radial contact to sweep a passage over distance. A fin brush must minimize deformation while reaching between or across thin fins. The same stiffness strategy cannot serve both.
HVAC Brush Customization
Working diameter, rod or shaft length, flexibility, trim, filament, connection and handle can be matched to the equipment. For coils, provide fin pitch and accessible face; for ducts, provide diameter, length and bends.
- Working diameter
- Rod or shaft length
- Flexibility
- Trim length
- Filament
- Connection
- Handle
Send the Airflow Path or Coil Geometry
Provide duct or vent size, run length, bends, coil or fin dimensions, contamination and cleaning method. We can then select a brush that reaches without creating damage.